Expert Articles on Commissioning, Testing & Balancing, Energy Consulting, Critical Environment Services.

Kitchen Exhaust Hood Testing and Balancing: FAQ on NFPA 96 Capture Velocity Requirements

Written by Nicholas Muscolino | Nov 18, 2026, 6:40:22 PM

Commercial kitchen exhaust hoods are tested by measuring airflow at the hood face and in the grease duct, comparing those readings against the system's design values and NFPA 96 requirements, and confirming makeup air enters on the right sequence without pulling the kitchen into excessive negative pressure. A hood that looks correctly sized on the mechanical drawings can still fail to capture smoke and grease-laden vapor if a damper was left throttled, a filter is loaded, or the duct run picked up extra resistance that the original design never accounted for. Field measurement is what confirms the hood is doing the job it was designed to do.

What Does NFPA 96 Require for Kitchen Exhaust Hoods?

NFPA 96, the Standard for Ventilation Control and Fire Protection of Commercial Cooking Operations, sets hood sizing on a performance basis rather than a single fixed number. Section 5.2 requires a hood to be sized and configured to capture and remove grease-laden vapors and smoke from the cooking equipment it serves, and the hood has to extend far enough beyond the equipment to do that. The International Mechanical Code reinforces this with a specific dimension: Section 507.4.1 requires at least a 6-inch overhang beyond the cooking equipment on any open side of the hood.

Exhaust rate requirements vary by hood type and duty classification. A wall-mounted canopy hood over light-duty equipment has a different exhaust requirement than an island canopy over heavy-duty, solid-fuel equipment, and the applicable mechanical code's exhaust rate table sets the minimum for each combination. ASHRAE 154, Ventilation for Commercial Cooking Operations, is the design reference most engineers use to size capture and containment for a given hood and appliance layout.

How Is Kitchen Exhaust Airflow Measured?

Field verification of kitchen exhaust airflow comes down to three methods, each with a different level of precision.

A pitot tube traverse of the duct, performed to AMCA 203 or ASHRAE 111 methodology, is the most accurate field method available. It averages multiple velocity readings across the duct cross-section through access ports, and it requires a trained technician and the right test ports, which is why it's the method a TAB report relies on for a documented baseline. A hot-wire anemometer reading taken at an access opening is faster and useful for a spot check, but it reads a single point rather than averaging across the duct, so it is less reliable as the sole basis for an acceptance reading. Comparing the fan's nameplate CFM against duct cross-sectional area gives only a rough estimate, since a fan rarely delivers its nameplate rating once filters have loaded with grease or the duct has picked up extra static resistance over time.

Airflow measurement matters most at four points in a hood's life: during TAB commissioning when the system is new, after a deep cleaning when there's a complaint about reduced capture, while troubleshooting visible smoke escaping the hood, and after any modification to the system, whether that's a new branch duct, a damper replacement, or a fan swap.

What Role Does Makeup Air Play in Hood Performance?

A hood can be perfectly sized and still underperform if the kitchen can't draw in enough replacement air. NFPA 96 Section 8.3.1 limits the negative pressure a kitchen can run while the exhaust system operates to 0.02 in. w.c., and the International Mechanical Code requires makeup air to be automatically controlled so it starts and stops in step with the exhaust fan rather than running independently. Makeup air supply temperature should stay within about 10°F of room temperature, both for comfort and because a large temperature differential at the register can disturb the capture pattern at the hood itself.

A kitchen pulling harder negative pressure than design, often because a makeup air damper is stuck or a unit was taken offline for repair and never brought back fully, is one of the most common reasons a correctly sized hood still loses capture at the edges. This is a makeup air problem, not a hood problem, and it shows up in field testing as a building pressure reading, not a duct velocity reading, which is why both need to be checked together.

How Does Grease Duct Velocity Factor Into Testing?

Grease duct velocity keeps grease particles suspended in the airflow stream rather than settling and accumulating inside the duct, where they become a fire hazard. Local mechanical code amendments commonly specify a minimum duct velocity in the 1,500 fpm range for Type I grease ducts, though the applicable figure depends on the jurisdiction's adopted code and any local amendments, so it's worth confirming the exact minimum with the AHJ rather than assuming a single number applies everywhere. Type II hoods, which handle only heat and steam rather than grease-laden vapor, are not subject to the same grease duct velocity minimums.

Duct velocity is calculated as airflow (CFM) divided by the duct's cross-sectional area, and it's measured the same way the hood face airflow is, typically by pitot tube traverse for a documented TAB reading. A duct running below the design minimum velocity is a maintenance and fire-risk issue even if the hood itself is capturing effluent correctly at the face, which is why a complete test includes both the hood face reading and the duct velocity reading rather than one or the other.

Table 1: Kitchen Exhaust Testing at a Glance

What's TestedMethodReferenceWhy It Matters
Hood face capturePitot tube traverse, hot-wire spot checkASHRAE 154, ASTM F1704 (lab rating)Confirms smoke and grease vapor are captured in the field, not only on paper
Grease duct velocityPitot tube traverse per AMCA 203 / ASHRAE 111Local mechanical code amendment, commonly ~1,500 fpm minimum for Type I ductsKeeps grease particles entrained instead of settling and building up as a fire hazard
Makeup air rate & sequenceAirflow measurement, building pressure reading at an exterior doorNFPA 96 §8.3.1 (0.02 in. w.c. max negative pressure); IMC §508.1Insufficient makeup air pulls negative pressure and disrupts hood capture even when the hood is correctly sized
Grease extraction efficiencyLaboratory rating, not a field testUL 710Rates how much grease the filter removes before air reaches the duct

Frequently Asked Questions

How often does a kitchen exhaust hood need airflow testing?

NFPA 96 does not set a single fixed interval for airflow testing itself. It ties cleaning frequency to cooking volume and equipment type, ranging from monthly for solid-fuel cooking to annual for low-volume operations, and most TAB providers recommend airflow verification at commissioning, after any deep cleaning that follows a capture complaint, and after any modification to the hood, duct, or fan. Check with the local AHJ, since some jurisdictions set their own inspection intervals on top of the NFPA 96 baseline.

What's the difference between hood face velocity and duct velocity?

Hood face velocity (or capture velocity) measures how well the hood pulls smoke and vapor off the cooking surface into the hood itself. Duct velocity measures how fast air moves through the grease duct afterward, which matters for keeping grease particles suspended rather than settling inside the duct. A hood can pass one measurement and fail the other, so a complete test checks both.

Can a hood be correctly sized and still fail a capture test?

Yes, and it's one of the more common findings in the field. A damper left throttled after a previous service call, a loaded grease filter restricting airflow, insufficient makeup air pulling the kitchen negative, or duct resistance that increased after the original design can all cause a correctly sized hood to underperform. Field measurement, beyond design review alone, is what confirms actual performance.

Does NFPA 96 apply to Type II hoods over dishwashers or steamers?

Type II hoods, which handle only heat and steam rather than grease-laden cooking vapor, follow a separate, lighter set of requirements under NFPA 96 and the applicable mechanical code. They are not subject to the grease duct velocity minimums or the fire suppression requirements that apply to Type I systems over grease-producing equipment.

Who performs kitchen exhaust airflow testing?

A TAB (testing, adjusting, and balancing) provider typically performs the airflow measurement, since the pitot tube traverse and makeup air verification are standard TAB field methods. Fire suppression system inspection and cleaning certification are separate scopes, usually handled by a fire protection or hood-cleaning contractor, so a restaurant or commercial kitchen often needs both providers working from the same documentation.

What should a building owner ask for after a kitchen exhaust TAB report?

Ask for the hood face airflow reading, the duct velocity reading, and the makeup air rate documented against the original design values, rather than a single pass or fail statement. Keeping that baseline on file makes it much faster to diagnose a capture complaint later, since a technician can compare a new reading against the commissioning baseline instead of starting from scratch.

Where to Start

A kitchen exhaust system that was never measured after installation, or hasn't been re-tested since the last major cleaning, is a common gap in restaurant and commercial kitchen facilities. Aero Performance Group's testing and balancing team measures hood face capture, grease duct velocity, and makeup air performance against design values and documents the results for your records.

Request a kitchen exhaust testing assessment